If water is present, it may have settled to the bottom and will drain out prior to the lubricant, or it may be mixed with the lubricant, giving it a milky colored appearance. If the vessel experiences any form of impact, have an authorized Mercury Marine dealer inspect and repair the vessel or power package. Positioning Outboard for Storage Store outboard in an upright vertical position to allow water to drain out of outboard. If not, consult your dealer for a description of the functions and operations of the remote control. Set the engine speed at idle and the gear shift in neutral to prevent the outboard from starting in gear. Immediately reduce engine speed after engine starts.
Warranty coverage becomes available upon proper registration of the product by the authorized dealer. Always use required components and follow instructions and torque procedures. Squeeze the fuel line primer bulb several times until it feels firm. Diameter C — Right-Hand and Left-Hand Rotation 5. Never operate the boat out of the water with a propeller installed. Pull out the filter assembly from mount. Warranty coverage becomes available upon proper registration of the product by the authorized dealer.
You are just one click away from the service manual you are searching for! When setting the friction adjustment, maintain sufficient steering friction to prevent the outboard from steering into a full turn if the tiller handle or steering wheel is released. Empty contents into an approved container. Refer to General Information - Lanyard Stop Switch. Lubricate the seal on the drain plug with oil and reinstall. Never operate the boat out of the water with a propeller installed. Outboard Remote Control Models The remote control connected to your outboard must be equipped with a start in neutral only protection device. Acquire and read the installation, operation, and maintenance manuals for all your selected accessories.
You can pay for your Mercury 4-Stroke Outboard Boat Motor service manual with Paypal or Visa, MasterCard or Discover. The most important tool in your toolbox may be your Clymer manual -- get one today. Place a block of wood between the propeller blade and the anti-ventilation plate. Rubber portion swollen by oil. Description Where Used Part No. Contact your boat manufacturer for specific recommendations on the boat's fuel system components fuel tanks, fuel lines, and fittings. The serial number is located on the outboard as shown.
Safe Boating Suggestions In order to safely enjoy the waterways, familiarize yourself with local and other governmental boating regulations and restrictions, and consider the following suggestions. Additional clearance may be required for railroad crossings, driveways and trailer bouncing. Check for a steady stream of water flowing out of the water pump indicator hole. Coat the propeller shaft with Quicksilver or Mercury Precision Lubricants Anti-Corrosion Grease or 2-4-C Marine Lubricant with Teflon. Before installing or removing a propeller, place the drive unit in neutral and engage the lanyard stop switch to prevent the engine from starting. Failure of any parts caused by lack of cooling water, which results from starting motor out of water, foreign material blocking inlet holes, motor being mounted too high or trimmed too far out.
Adjust cable barrel until the barrel slips onto the mounting stud. Be sure at least one additional person on board is instructed in the basics of starting and operating the outboard and boat handling in case the driver is unable to operate the boat. Each month, spray Mercury Precision or Quicksilver Corrosion Guard on external metal surfaces. This is the same manual professional technicians use to diagnose and repair the outboard motor. Throttle cable locknut Reinstall the access cover with two bolts. These locknuts must never be replaced with common nuts non-locking as they will work loose and vibrate off, freeing the link rod to disengage. That means you get the manual you need right away without having to wait for shipping.
Coat the propeller shaft with Quicksilver or Mercury Precision Lubricants Anti-Corrosion Grease or 2-4-C Marine Lubricant with Teflon. From basic maintenance and troubleshooting to complete overhauls, our Mariner Outboard manuals provide the information you need. Provide a sufficient supply of water to the water inlets during operation. Align the cable end guide with this center mark when installing cable to the engine. Acquire and read the installation, operation, and maintenance manuals for all your selected accessories. From basic maintenance and troubleshooting to complete overhauls, our Mercury Outboard manuals provide the information you need.
Customer Service Mercury 4-Stroke Outboard Boat Motor Service Manuals - Marine Service Manuals has made every effort to make your Mercury 4-Stroke Outboard Boat Motor service manual shopping experience as easy as possible. This enables the operator to easily adjust the position of the outboard by pressing the trim switch. Moving the outboard in closer to the boat transom is called trimming in or down. See your dealer for touch-up paint. Description Where Used Part No. However, the boat will not complete a full circle. See Flushing the Cooling System.