93 suzuki swift owners manual file. SUZUKI SWIFT USER MANUAL Pdf Download. 2019-02-26

93 suzuki swift owners manual file Rating: 9,8/10 237 reviews

Suzuki Swift Workshop & Owners Manual

93 suzuki swift owners manual file

For this purpose, use of such an inspection form will facilitate collecting information to the point required for proper analysis and diagnosis. Check its resistance and operation using the same procedure as that for main relay. Is it in good condition? Replace engine See Section 6E1. Tightening Torque c : 11 N m 1. Condition Possible Cause Referring Item Hard Starting.

Next

Reading : 93 Suzuki Swift Repair Manual

93 suzuki swift owners manual file

D Before measuring voltage to check for electrical system, check to make sure that battery voltage is 11 V or higher. D Using a cylinder gauge, measure cylinder bore in thrust and axial directions at two positions as shown in figure. Beyond 90,000 km 54,000 miles , carry out the same services at Interval: the same intervals respectively. D Install clamps 3 as shown in figure, and tighten bolts and nuts to specification. Vehicle balance on hoist may change depending of what part to be removed. If desired section, item or description is not found in it, try next one in the list and do the same one by one till what is being searched is found. Then the signal causes the door lock controller to lock and unlock the door.

Next

Reading : 93 Suzuki Swift Repair Manual

93 suzuki swift owners manual file

Refer to figure for proper installation of these parts. If any damage or wear is found, replace parking lever. Connecting rod bearing surfaces of each part. If oil level is low, add oil up to Full level mark on oil level gauge. D After servicing fuel, oil, coolant, vacuum, exhaust or brake systems, check all lines related to the system for leaks.

Next

SUZUKI SWIFT USER MANUAL Pdf Download.

93 suzuki swift owners manual file

This interval should be judged by This interval should be judged by 1,000 odometer reading or months, whichever comes first. Terminal Standard resistance A — B C — B 20 — 24 Ω F — E D — E 1. If any malcondition is found, replace camshaft or cylinder head with housing. Guide seal 1 Remove oil level gauge guide bolt 3 and pull out guide 2 from oil pump 1. D Crankshaft timing belt pulley teeth damaged.

Next

Reading : 93 Suzuki Swift Repair Manual

93 suzuki swift owners manual file

Is it in good condition? Does speedometer indicate vehicle speed? Intermittent trouble or Go to Step 3. With crankshaft locked using flat end rod or the like 5 , tighten crank timing belt pulley bolt 4 to specified torque. Check each part which is suspected to be the cause. Check exhaust system for leakage, loose Go to Step 3. Such terminal voltage check at low battery voltage will lead to erroneous diagnosis.

Next

Reading : 93 Suzuki Swift Owners Manual File

93 suzuki swift owners manual file

The Swift was powered by a new generation of Suzuki inline-four gasoline engines, the M family. D When installing the wiring harness, fix it with clamps so that no slack is left. Replace output 1 Disconnect output shaft speed sensor connector with shaft speed. Check its resistance and operation using the same procedure as that for main relay. Fit them sequen- tially in ascending order, 1, 2, 3, 4 and 5, starting from pulley side.

Next

Download 2011 Suzuki Swift Owners Manual Printable File PDF E

93 suzuki swift owners manual file

Throttle body 3-way joint 4. Tighten bolts and nuts to specified torque. Gasket : Do not reuse 8. Transmission Go to Step 3. Repeat this 3 or 4 times and then check fuel pressure. The coolant in the radiator expands with heat, and the overflow is col- lected in the reservoir tank.

Next

Reading : 93 Suzuki Swift Repair Manual

93 suzuki swift owners manual file

D Crankshaft timing belt pulley teeth damaged. If crank pin is dam- aged, or out-of-round or taper is out of limit, replace crankshaft or regrind crank pin to undersize and use undersize bearing. Is it barometric pressure approx. Are circuits in good condition? Oil lip portion of oil seal before installing. If turned, interference may occur among piston and valves, and parts related to piston and valves may be damaged. Measure crank pin for out-of-round or taper with a micrometer. Tightening Torque a : 3.

Next